| |
|
| Item number: CIEN4-36659656 Manufacturer no.: 3362365 EAN/GTIN: n/a |
| |
|
| | |
| Need more hours in your day?
Save time by NOT breaking the loop on 4-20 mA signal measurements.
Are you spending time:
Taking mA measurements by removing a wire and breaking the loop Calling the control room to isolate a loop Testing analog input/output on a console Troubleshooting devices with mA inputs and outputs Repairing intermittent or erratic 4-20 mA loops Going back to the shop to get extra tools
If you need more time in your busy day take a good look at the Fluke 773 mA Clamp Meters. It’s designed to save you time, and money, by eliminating time wasting activities. Now you can troubleshoot and repair 4-20 mA loops without breaking the loop or bringing down the system.
Here are some specific ways the Fluke 773 Clamp Meters will help you:
Milliamp Clamp Features
Measure mA signals for PLC and control system analog I/O without breaking the loop
- Measures low level dc current - Correlate process indication with real physical value
Measure output signals from transmitters without breaking the loop
- Maintain and troubleshoot process and automation equipment without breaking the loop - No disruption to the process
Detachable clamp with extension cable
- Measurements in tight locations - Enables measurements in difficult situations
Measurement Spotlight
- Illuminates hard to see wires in dark enclosures - Measurement process is easier and quicker
Measure up to 99.9 mA range non-contact
- Wide range of measurements - Measures 10 to 50 mA signals in older control systems
Automatic power off
- After 15 minutes and 2 minute automatic off for backlight and spotlight - Saves battery life
- Best in class 0.2% accuracy - 0.01 mA resolution and sensitivity - Measure 4 to 20 mA signals without “breaking the loop” - Measure mA signals for PLC and control system analog I/O - Dual backlit display with both mA measurement and percent of 4 to 20 mA span - Measurement Spotlight illuminates hard to see wires in dark enclosures - Detachable clamp with extension cable for measurements in tight locations - Measure 10 to 50 mA signals in older control systems using the 99.9 mA range - Automatically change the 4 to 20 mA output for remote testing - Power saving features, auto-off, backlight timeout extend battery life - Hold function captures and displays changing measurements - Measure 4 to 20 mA signals with in-circuit measurement - Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters - Source 4 to 20 mA signals for testing control system I/O or I/Ps - mA output linear ramp or 25% step output - Automatically change the 4 to 20 mA output for remote testing - DC voltage measurement to verify 24V power supplies or voltage I/O signals - Source DC voltage to test input devices that accept a 1-5V or 0 to 10V signals - Scaled mA output provides a continuous mA signal that corresponds to the 4 to 20 mA signal measured by the mA clamp - Enables milliamp signal logging to a separate logging device without breaking the loop - Output mA signal enables a logging DMM or other device to record the 4- to 20 mA signal without breaking the loop - mA in/out: simultaneously measure the mA signal with the clamp and source a mA signal - Apply a mA input signal to a device and measure its’ 4-20 mA output on devices such as valves or mA isolators - Voltage output linear ramp or 25% step output - Automatically change the voltage output for remote testing More information: Power | Power source | Battery | | Battery type | AA | | Number of batteries supported | 4 | | Battery technology | Alkaline | | Battery voltage | 1.5 V | Technical details | Product type | Digital multimeter | | Placement supported | Handheld multimeter | | DC voltage range | 0 - 30 V | | DC current range | 0 - 0.024 A | | Basic accuracy (DC current) | 0.2% + 2 counts | | Basic accuracy (DC voltage) | 0.2% + 2 counts | | Product colour | Grey, Red, Yellow | Weight & dimensions | Width | 70 mm | | Depth | 44 mm | | Height | 246 mm | | Weight | 410 g | Operational conditions | Operating temperature (T-T) | -10 - 50 °C | | Storage temperature (T-T) | -25 - 60 °C | | Operating relative humidity (H-H) | 0 - 90 % | | Operating altitude | 0 - 2000 m | Display | Display | LCD |
|
| | |
| | | |
| Other search terms: Universal pincers, Universal pincer, Nail puller, Nail pullers, Digital multimeter, Digital multimeters, Multimeter, Multimeters, Circuit analyzer, Circuit analyzers, Multi meter, Multi meters, Process display, Clamp meter, Clamp ammeter, fluke multimeter, ampere meter |
| | |
| |