Cable Trunking System Accessories (89 items)

Used to protect the insulation against damage and keep heat loss to a minimum.

Designed so that the maximum number of support and framing applications can be constructed with a minimum amount of labor and pieces. Used to mount, brace, support or connect structural loads in bu...

Saves installation time by allowing conduit or pip to be laid in place after the hanger is mounted For use with conduit and pipe

Assembly includes steel clamp with bolt/locknut and cushion. To secure pipes, tubes and hoses for fluid conductors.

A Liquidtight Fitting to Secure Flexible Cord or Power Cable to a Box or Enclosure and Provide Strain Relief.

Assembly includes steel clamp with bolt/locknut and cushion. To secure pipes, tubes and hoses for fluid conductors.

Splices large conductors required for commercial service, use as low cost reducing sleeve. All sizes can be installed with popular mechanical and hydraulic tools. Center stop assures proper conduct...

Uncoated For Temperatures up to 300 Degrees Celsius (572 F) for Indoor and Outdoor Applications, Suitable for High Temperature Environments

Extruded Grommeting, Natural Nylon 6.6 for Temperatures up to 85 Degrees Celsius (185 F), Height of 5.08mm (0.20 Inches), Width of 4.32mm (0.17 Inches), Thickness 1.14mm (0.045 Inches), Width Maxim...

Extruded Grommeting, Natural Nylon 6.6 for Temperatures up to 85 Degrees Celsius (185 F), Height of 5.58mm (0.220 Inches), Width of 5.21mm (0.205 Inches), Thickness 1.27mm (0.05 Inches), Width Maxi...

Extruded Grommeting, Natural Nylon 6.6 for Temperatures up to 85 Degrees Celsius (185 F), Height of 7.11mm (0.28 Inches), Width of 9.40mm (0.37 Inches), Thickness 1.27mm (0.05 Inches), Width Maximu...

Made of flexible PVC compound - Easy to apply - Protects cables from chafing on bulkheads PVC Beading strip is used to protect cables routed through sharp-edged cutout sections. It can also be used...

Lay-in Hinged Cover Nipples are used for adjusting wireway length.

Lay-in Hinged Cover Nipples are used for adjusting wireway length.

Feed-Through Stainless Steel Tees are used for making T-type turns in wireway runs. Connects to other wireway sections and fittings and protects wires and cables in frequently hosed down, very wet ...

Lay-in Hinged Cover Nipples are used for adjusting wireway length.

This dust protector can be placed under the cap nut of below mentioned SKINDICHT® types and specified SKINTOP® cable glands. Delivery will be made in the largest possible packing unit (bulk goods),...

Fastening of the bracket to the U support of width 400 mm or greater using hexagonal bolt through both sides of the support. Please insert suitable spacers.

Blanking lid for closing off a square Modul 45 mounting opening in a mounting box cover plate.

Adjustable connector for cable trays with a side height of 60 mm. Including appropriate fastening material.

Straight connector for straight connection of cable trays and fittings with a side height of 60 mm.

End piece to close the WDK trunking.

End piece for closing the WDK trunking.

Allows cable tie entry from all four sides - Available in multiple sizes to match application load requirements - Provides 2-up for fast and easy liner removal to speed Rubber Adhesive - General pu...

4-Way adhesive backed cable tie mount, high temp, .75"x.75" (19.1mm x 19.1mm), white, standard package.

Duct cover with protective film, 1.5 W x 6' length, PVC, light gray.

Round hole design retains and supports wires at variable heights and positions to enhance wire management. Smooth round edges to prevent wire abrasion. Base scoreline for easy removal for T-junctio...

Schneider Electric INS45026