Development Tool Accessories (241 items)

iButton™ Clip. DS9094F. Printed Circuit Board mount holder for 16.3mm F5 MicroCan.

Accessory Type = Development Kit For Use With = Windows Based GUI Tool Application = Industrial Use, Medical Imaging

SEGGER EmulatorThe SEGGER emulator is used with J-LINK Plus debug probe. This ARM/Cortex emulator and Renesas RX emulator include a USB cable and a 0.1in, 20-pin JTAG/SWD ribbon cable for ARM/Corte...

The Analog Discovery Studio is a fully functional, portable test and measurement device that can turn any cross-functional space into a pop-up electronics laboratory. Equipped with 13 instruments, ...

The Broadcom spectrometer slit evaluation kit gives the chance to increase the spectral sensitivity of Qmini or Qwave spectrometer. It includes four SMA adapters with integrated entrance slits of 5...

Reduced form factor ARM/Cortex Debug Probe, Microchip PIC32 Debug Probe, Renesas RX Debug Probe, and SiLabs EFM8 / C8051 Debug Probe. Includes a USB cable, and a 20-pin, 0.1″ ribbon cable. Addition...

MPLAB PM3 Universal Device Programmer Accessories

Power Debugger. The Power Debugger is a powerful development tool for debugging and programming AVR microcontrollers. The tool is using UPDI, JTAG, PDI, debugWIRE, aWire, TPI or SPI target interfac...

J-Link ARM SWD Isolator Board. The J-Link SWD Isolator can be connected between a J-Link Probe and an ARM-board with a 20-pin debug connector to provide electrical isolation. This is essential when...

The SEGGER J-Link Mictor 38 Adapter connects the standard 20-pin 0.1″ J-Link interface to the 38-pin Mictor interface. The pinout follows the single target connector pinout specification as defined...

The FMC Pcam (CSI-2 interface) Adapter is a cost-effective way to add cameras to your FPGA or APSoC development board with the high speed, FMC connector. The FMC Pcam Adapter enables designers to d...

Accessory Type = Socket Board For Use With = mikroBUS 3-Lead Contact Socket Board'

SEGGER Microcontroller AdapterThe SEGGER Microcontroller adapter is J-Trace MICTOR 38 adapter that connects to the 38-pin MICTOR connector. It connects the GND, JTAG and some trace pins to their co...

STK600 Starter Kit Socket Cards. This range of socket cards from Atmel allows you to connect a range of different pin type and size devices to the ATK600 Starter Kit. •PDIP8/14/20/28/40 ; 720-0143 ...

Power Supply for MPLAB® ICE 4000/PM3 3-5 V. The ACICE0401 is a 3-5 V power supply for the MPLAB® ICE 4000 emulation system and the MPLAB® PM3 Universal Device Programmer.

Accessory Type = Development Kit For Use With = controlCARDs, HSEC180 controlCARDs Application = MCU Development

J-Link 10-Pin Needle Adapter. The J-Link 10-pin Needle Adapter has been designed to connect a J-Link Probe to a PCB which does not have a mating connector or programming header. Compatible Probes. ...

The SEGGER J-Link 6-pin Needle Adapter has been designed to connect J-Link to a PCB which does not come with a mating connector or programming header.No additional connector required on your PCB Ve...

Generic STK600 socketcard for devices in TQFP100 package, 0.5 Pitch, 14x14 body size.

The SEGGER J-Link Measurement+Patch Adapter provides test points for all debug signals to allow easy access for test probes. It has a standard 20-pin 0.1″ socket towards the J-Link debug probe and ...