Power, Motor & Robotics Development Tools (275 items)

BUCK click is a buck switching regulator that accepts a wide input voltage range of up to 40V and steps it down to 3.3V or 5V. The click carries the LT3976 40V, 5A, 2MHz step-down switching regulat...

Click board comes with the header strips soldered. PWM click mikroBUS™. PWM click is a mikroBUS add-on board for controlling sixteen PWM (Pulse Width Modulation) outputs through a single I²C bus in...

Click board comes with the header strips soldered. Relay2 click mikroBUS™. Relay2 click is a mikroBUS add-on board for adding two solid state relays. It features two of the LCA717, Single-Pole, Nor...

Fan click carries an EMC2301 controller for powering and regulating the operation of 5V four-wire fans, which are commonly utilized as coolers in computers and other electronics. The controller sup...

Click board comes with the header strips soldered. HAPTIC click mikroBUS™. The Haptic click is an add-on board that driver ERM (Eccentric Rotating Mass) and LRA (Linear Resonant Actuator) vibration...

Click board comes with the header strips soldered. Stepper 3 click mikroBUS™. The Stepper 3 click is an add-on board that driver unipolar stepper motors with precise controls. A high-voltage, high-...

Click board comes with the header strips soldered. Signal Relay click mikroBUS™. Signal Relay click is a mikroBUS add-on board for adding ON/OFF signal control with four relays. It features the Omr...

Click board comes with the header strips soldered. PWM driver click mikroBUS™. PWM driver click is a mikroBUS add-on board for controlling the DC motor speed or fast switch ON/OFF a DC load circuit...

Click board comes with the header strips soldered. Ammeter click mikroBUS™. Ammeter click is a mikroBUS add-on board for measuring DC current of an electrical circuit. When current passes through a...

Click board comes with the header strips soldered. Voltmeter click mikroBUS™. Voltmeter click is a mikroBUS add-on board for measuring DC voltage of an electrical circuit. Measurement range from ze...

Click board comes with the header strips soldered. Brushless click mikroBUS™. The Brushless click is an add-on board that drives 3-phase full-wave Brushless DC motors. A PWM Sensorless Controller I...

Power Management Function = LDO Voltage Regulator For Use With = LM317-M, MCP3204, MCP4921 Kit Classification = Module, Power Supply Kit Name = VREG Click

AC Current Sensor with voltage output is not included. Also available is the AC Current click - bundle (MIKROE-2525). Click board comes with the header strips soldered. AC Current click mikroBUS™. ...

Click board comes with the header strips soldered. AC Current click mikroBUS™ - Bundle. With AC Current click bundle (AC Current click + AC Current Sensor), you are able to measure alternating curr...

LEM click carries the LTS 6-NP current transducer and MCP3201 ADC converter. The click can measure AC and DC current with exceptional speed, up to 200 KHz. LEM click is designed to run on either 3....

MIC24045 click carries MIC24045 I2C-programmable, high-efficiency, wide input range, 5A synchronous step-down regulator from Microchip. The click is designed to run on either 3.3V or 5V power suppl...

MCP73213 click carries the MCP73213 dual-cell Li-Ion/Li-Polymer battery charge management controller with input overvoltage protection from Microchip. The click is designed to run on either 3.3V or...

Compatible Design Upgrade 3D Printers Printers, POS Office and home automation Textile, Sewing Machines CCTV, Security ATM, Cash recycler HVAC2-phase stepper motors up to 2A coil current (peak) STE...

DC MOTOR 5 click carries the DRV8701 brushed DC motor gate driver from Texas Instruments. The click is designed to run on an external power supply. It communicates with the target MCU over the foll...

Slider click features a mechanical slide action potentiometer - a slider, which gives a nice feeling when actuating, along with 16 SMD LEDs, that can be used for any kind of visual feedback. The on...

Fan 2 click carries the MAX31760 precision fan-speed controller. It can measure temperature and adjust the fan speed to keep the temperature at the same level. Fan 2 click can also control two fans...

BUZZ 2 click carries the CMT-8540S-SMT magnetic buzzer transducer. The buzzer’s resonant frequency is 4kHz. The click is designed to run on either 3.3V or 5V power supply.

Stepper 4 click can be used for driving a stepper motor and controlling its step resolution, rotation direction, and time between the steps. It has output drive capability of 2A. The click carries ...

Power Management Function = Boost Converter For Use With = Battery Powered Products Kit Classification = Boost Converter Board Featured Device = TPS61230A Kit Name = Boost 4 Click

Brushless 3 click carries the DRV10983, a three-phase sensorless motor driver with integrated power MOSFETs. When an external power supply is applied, you can drive a brushless DC motor through the...

Buck-Boost click™ features LTC3129-1, a buck-boost DC/DC conversion integrated circuit from Linear Technology®. The click supports a wide input voltage range and can output eight discrete regulated...

There are many battery chargers and solar energy harvesters out there already, but the Solar energy click has the unique feature - it encompasses both of these devices in a single package. The clic...

For Use With = Cellphones, Pagers Kit Classification = mikroBus Click Board Featured Device = C1026B002F Kit Name = Vibro Motor Click

Power Management Function = Buck Regulator For Use With = Router, Server Kit Classification = mikroBus Click Board Featured Device = MCP4921, MIC24055 Kit Name = MIC24055 Click

Power Management Function = Fan Controller For Use With = Fan Kit Classification = mikroBus Click Board Featured Device = MIC74 - 2, MIC29152 Kit Name = Fan 3 Click

Power Management Function = BLDC Motor For Use With = BLDC Motors Kit Classification = Motor Driver Board Featured Device = ATmega8A Kit Name = Brushless 6 Click

Power Management Function = Battery Charger For Use With = Lithium-ion, Lithium-Polymer Batteries Kit Classification = Battery Charger Controller Board Featured Device = MCP 4161, MCP 73113 Kit Nam...

Power Management Function = Battery Charger For Use With = Lithium-ion, Lithium-Polymer Batteries Kit Classification = Battery Charger Controller Board Kit Name = MCP73871 Click

DIGI POT 4 click is a digitally controlled dual potentiometer, with the resistance of 10KΩ. It has a 10bit resolution which allows for a very smooth linear wiper positioning through 1024 steps. Dig...

MikroElektronika 8 Click DC Motor DriveThe MikroElektronika is an 8-click DC motor driver. This motor driver can drive DC motors with brushes, providing them with a significant amount of current an...

MikroElektronika MIKROE-2894 DC-DC Click BoardThe MikroElektronika MIKROE-2894 is a BOOST 2 click DC-DC click board regulator has a fixed 5V output, which can be obtained from any low voltage input...

BATT-Man click BATT-MAN click is a very versatile battery operated power manager. When powered via mikroBUS™, it will charge the connected Li-Ion/Li-Po 3.7V battery, while providing the output volt...

MikroElektronika PAC1921 click Power Monitoring and Measuring DeviceThe MikroElektronika PAC1921 click is a versatile power monitoring and a measuring device which is used for high speed, low laten...

MikroElektronika 7 Click Stepper Motor DriveThe MikroElektronika stepper 7 click is a bipolar step motor driver. This stepper 7 click carries a port expander so that communication can be done with ...

MikroElektronika Buck-Boost Converter Click BoardThe MikroElektronika Buck-Boost converter click board is a buck-boost voltage regulator, a switching regulator topology that combines principles of ...

MikroElektronika Buck 6 Click BoardThe MikroElektronika Buck 6 click board is an advanced synchronous DC-DC step down (buck) converter, with a very wide input voltage range from 5V to 30V and reaso...

MikroElektronika Buck-Boost 2 click boardThe MikroElektronika Buck-Boost 2 click board is an advanced DC-DC step-down/step-up regulator (buck/boost) click 2 board, which can provide regulated 5V on...

Position Sensorless BLDC Drivers (no Hall Sensor required) 180° Sinusoidal Drive for High Efficiency and Low Acoustic Noise Supports 2V to 14V Power Supplies Speed Control through Power Supply Modu...

Brushless 5 click is a 3 phase sensorless BLDC motor controller, with a soft-switching feature for reduced motor noise and EMI, and precise BEMF motor sensing, which eliminates the need for Hall-se...

Micropower Operating Current (0.9μA typ, 1.7μA max) Preserves Battery Power Tiny 1.11mm x 0.76mm 6-Bump WLP and SOT23 Packages Save Board Space Internal Precision Reference Saves Space and Cost of ...

Factory trimmed AC and DC current sensor analogue ratiometric output voltage Combining sensing element, signal conditioning & isolation in small foot print and low profile SOIC package No applicati...

Output Voltages: 3.2V to 12.775V and –1.2V to –13.95V (LT3582) 5V and –5V (LT3582-5) 12V and –12V (LT3582-12) Digitally Re-Programmable (LT3582) via I2C for: Output Voltages Power Sequencing Output...

Servo click is a 16-channel PWM servo driver with the voltage sensing circuitry. It can be used to simultaneously control 16 servo motors, each with its own programmable PWM signal. The frequency o...

PWR Meter 2 click is a compact and accurate power monitoring Click board™, capable of measuring and monitoring voltage up to 24V and current up to 5A. It carries the MCP3910, an integrated analogue...

PWR Meter click is a power measurement Click board™, capable of measuring voltage and current through the load, connected to either AC or DC power source. PWR Meter click uses the MCP39F511A, a ver...

Fan 4 click is a very compact, two-wire fan driver. It utilizes an integrated 5V, DC, brushless-motor driver chip. Its output voltage regulation and current limiting capabilities allow the speed co...

3xBuck click is a triple step-down (buck) converter Click board™. It features three independent output terminals that can provide 1.8V, 3.3V, and 5V with the combined current output up to 3A. This ...

Stepper 6 click is the complete integrated bipolar step motor driver solution. It comes with the abundance of features that allow silent operation and optimal working conditions for the connected m...

Power Management Function = Buck-Boost Converter Kit Classification = Boost Converter Board Featured Device = ISL85403 Kit Name = Buck-Boost 3 Click

DC MOTOR 7 click is a dual brushed DC motor driving Click board™, featuring the advanced PWM chopper-type integrated DC motor driver, labeled as TB67H400AFTG. This IC can drive two brushed DC motor...

Opto 3 click is a relay Click board™, equipped with two pairs of optically isolated solid-state relays (SSR). One pair of SSRs is used to provide a reinforced galvanic isolation for the external si...

DigiVref click is a very precise voltage reference Click board™, which allows one of four different voltage values to be selected over the SPI interface. Once the selection is done, the voltage ref...

Opto 4 click is a galvanically isolated power switch, which uses a power MOSFET in combination with an optocoupler. The power MOSFET can withstand significant current due to its low ON resistance, ...

Charger 8 Click is an intelligent Li-Ion battery charger, system power manager, and a battery fuel gauge Click board™. As a system power distributor, it can supply up to 2A to a connected load. By ...

Relay click 3 is a dual relay Click board, featuring two single-pole double-throw relays which can be operated by output pins of the host microcontroller (MCU). It offers an elegant and easy soluti...

DC Motor 9 Click is a brushed DC motor driver with the current limiting and current sensing. It is based on the DRV8871, an integrated H-Bridge driver IC, optimized for motor driving applications. ...

Buck 11 click is a high-efficiency step-down converter which provides 3.3V on its output, derived from the connected power supply voltage, in the range from 4.2V to 60V. Buck 11 click is based on t...

The MikroElektronikas L meter click, It is 5V compact and accurate single high-speed voltage comparator, capable of measuring and monitoring. It measure a wide range of inductance. It is compatible...

Power Management Function = Motor Driver For Use With = BLDC Motors Kit Classification = Motor Driver Board Kit Name = STSPIN233 Click

Charger 9 click is a Li-Ion (Li+, Li-Po) battery charger, capable of charging one, two or three battery cells. It is based on the MAX1757, an integrated Li+ battery charger with many features that ...

DC Motor 11 Click is a brushed DC motor driver with the current limiting and current sensing. It is based on the DRV8830, an integrated H-Bridge driver IC, optimized for motor driving applications....

The MikroElektronika Charger 11 Click is a LiFePO4 battery charger. It has two battery charger, The one is MCP4161 which offer a wide range of product offering using a SPI interface and second one ...

The MikroElektronikas Buck 13 Click is a high-efficiency step-down converter which provides a highly regulated output voltage derived from the connected power source, rated from 4.5V to 5.5V. The r...

The MIKROE Step up Click is a fixed frequency DC-DC step-up regulator that can integrate NMOS switch. This click board are fully tested product and ready to be used on a system operated with the mi...

The MikroElektronika Vibro Motor 2 click, It is eccentric rotating mass motor. It contains a small eccentric weight on its rotor, so while rotating it also produces vibration effect. This kind of m...

The MikroElektronika silent step lick, It is a high performance stepper motor controller and driver IC with serial communication interface. The driver ensure absolutely noiseless operation combined...

1The MikroElektronika MIKROE-3736 (stepper 13 Click) is a bipolar step motor driver. It also carries a port expander so that the communication can be done with a minimal number of pins, through the...

1The MikroElektronika MIKROE-3737 (balancer 3 Click) is overvoltage protection device for 2-series cell lithium-ion battery packs that incorporates a high-accuracy precision overvoltage detection c...

1The MikroElektronika MIKROE-3741 (BATT-MON Click) is a very versatile, high accuracy, multiple-chemistry battery gauge for applications single-cell batteries. It can be used mostly in smartphones,...

1The MikroElektronika MIKROE-3744 (Charger 12 Click) is a single lithium-ion (Li+) cell or three-cell NiMH/NiCd battery charger. This click board can be used for Low-Cost Li-Ion battery chargers, o...

Power, Motor & Robotics Development Tools

The MikroElektronika h-bridge 4 click, It has 18V 2ch H-bridge motor driver IC. It can drive two DC motor or one stepping motor. The Operating temperature range -30°C～85°C.Motor operating voltage r...

The MikroElektronika boost-6 click It is 2.2-MHz, 60-V Output Step Up DC/DC Converter. It is a monolithic high-voltage switching regulator with integrated 3-A, 60-V power MOSFET. The device can be ...

The MikroElektronika single cell click, It is a Click board which features MCP16251 synchronous boost regulator with true load disconnect and MCP1811A low-dropout (LDO) linear regulator that provid...

Power Management Function = Step-Down Converter Kit Classification = Converter Module Featured Device = BMR4613001 Kit Name = Buck 14 Click

Power Management Function = Motor Control For Use With = DC Motors, Inductive Loads Kit Classification = Motor Control Board Featured Device = MP6515GF-Z Kit Name = H-Bridge 5 Click

Power Management Function = Fan Controller For Use With = DC Fans Kit Classification = mikroBus Click Board Featured Device = EMC2103 Kit Name = Fan 6 Click

Power Management Function = DC Motor Driver Kit Classification = Motor Driver Board Featured Device = TLE 6208-6 G Kit Name = DC Motor 10 Click

Power Management Function = Step-Down Regulator For Use With = LNMs, PLCs Featured Device = L6986HTR Kit Name = Step Down 2 Click

Power Management Function = DC Motor Driver For Use With = Boats, RC Cars Kit Classification = Motor Driver Board Featured Device = TB67H450FNG. Kit Name = DC Motor 14 Click

Power Management Function = Power Monitor For Use With = Battery Chargers Kit Classification = Add On Board Featured Device = NA260AIPWR Kit Name = VCP Monitor Click

Power Management Function = Protection Functions For Use With = Power Tools Kit Classification = mikroBus Click Board Featured Device = MCP3202 Kit Name = Balancer 2 Click

Power Management Function = Battery Charger For Use With = Power Banks Kit Classification = Expansion Board Featured Device = MP2632B Kit Name = PowerBank Click

Power Management Function = Intelligent Power Switch For Use With = PC's, PDAs Kit Classification = mikroBus Click Board Featured Device = TPS2115APWR Kit Name = DC Motor 6 Click

Power Management Function = DC Motor Driver For Use With = Boats, RC Cars Kit Classification = Motor Driver Board Featured Device = TB67H451FNG Kit Name = DC Motor 6 Click

The MikroElektronika Stepper 14 Click is a Click board™ that features the DRV8847PWPR, a step motor driver, from Texas Instruments. This Click board™ provides a bipolar step motor control, It featu...

Power Management Function = Current Measurement, Voltage Measurement For Use With = ECU Kit Classification = mikroBus Click Board Featured Device = INA3221-Q1 Kit Name = VCP Monitor 2 Click

The MikroElektronika Stepper 10 Click is a two-phase bipolar stepping motor driver capable of controlling one stepper motor with PWM constant current drive. Clicks featured chip TB67S128FTG, from T...

The MikroElektronika Stepper 8 Click is a motor control add on board based on TC78H670FT from Toshiba, a clock-in and serial controlled Bipolar Stepping Motor Driver which can drive a 128 micro-ste...

The MikroElektronika Brushless 7 Click is, as its name said, a motor driver based expansion board for controlling BLCD motors with any microcontroller. The board is based on TC78B009FTG IC from Tos...

Power Management Function = Intelligent Power Switch For Use With = Power Supplies Kit Classification = Add On Board Featured Device = MAX890L Kit Name = Current Limit Click

Power Management Function = Motor Controller For Use With = TC78B042FTG Kit Classification = Controller Board Kit Name = Brushless 8 Click

The MikroElektronika Boost 3 Click is a compact add-on board that contains a boost converter with an integrated current mirror function. This board features the TPS61391, a 700-kHz pulse-width modu...

Power Management Function = Motor Driver For Use With = VNHD7008AY Kit Classification = Motor Driver Board Kit Name = H-Bridge 6 Click

Power Management Function = USB Power Controller Kit Classification = Sensor Add-On Board Featured Device = STUSB4500 Kit Name = USB -C Sink Click